Safety Nets Flammability Tester

Safety Nets Flammability Tester SL-FL32

Get in Touch

Safety Nets Flammability Tester Information

Application:
It is suitable for different safety nets, Fine mesh safety vertical net flammability resistance Performance.

Technical parameters:
1. Touch screen display / control
2. The equipment is divided into two parts: touch screen control box and combustion box.
3. The front part of the combustion box is a tempered glass observation door
4. The top of the box is evenly distributed with 16 vent holes, the inner diameter is 12.5mm; there are 6 vent holes on both sides of the combustion box, and the inner diameter is 12.5mm.
5. Top of the box is attached to the top
6. The top of the box is equipped with a hanging clamp, and the bottom of the style clamp is located 17mm above the highest point of the igniter nozzle.
7. Gas source: industrial grade propane, butane or propane / butane mixed gas, using methane gas with a purity of not less than 97% when the sample is pretreated according to 7.3
8. Power supply voltage and power: 220V±10% 50HZ Power less than 100W
9. Single-chip control, digital display automatic timing
10. Yu Yan, afterglow time: the longest 0-99M99S
11. Bunsen burner blue flame height: 15mm-175mm can be adjusted freely, with flame height scale
12. Touch screen related parameters:
a. Communication interface RS232, 3.3V CMOS or TTL, serial port mode
b. Use pure hardware FPGA driver display, “zero” startup time, run on power
c. Using M3+FPGA architecture, M3 is responsible for command parsing, FPGA focuses on TFT display, speed and reliability are leading the same scheme
d. The main controller uses a low-power processor to automatically enter the energy-saving mode.

The size of the combustion box	330330765mm.
The inner diameter of the igniter nozzle	11mm
vertical line angle	25°.
Ignition time	accurate to 0.05s
Sample size	500±5
Ambient temperature	-10 ° C ~ 30 ° C
Bunsen burner flame time	0-99M99S, can be arbitrarily set, accuracy ±0.01s
Bunsen burner automatic ignition time	arbitrary setting
Size	7 inches Effective display size Length 15.5cm Width 8.6cm
Resolution	800*480
Storage capacity	1G

Design standards:
GB 5725-2009 safe net

Applicable standards:
GB5455-2014 "Textiles Combustion performance Vertical release Damage length, smoldering and afterflame time determination"

News Center

> What is the ASTM D1230, FTMS191-5908 45 Degree Automatic Flammability Tester

Used to determine the burning characteristics of textiles under controlled conditions， the 45°Automatic Flammability Chamber automatically times the flame spread in 0.I second increments from ignition. The time starts when the flame impinges and stops when the sample's trigger string burns through. The flame burns ata45°angle under controlled flame-impingement at the tip of a stainless steel hypodermic needle with automatic flame impingement times of I,5 or 20 seconds available. The flame-imping...

> How to use Flammability Tester Of Building Material

Flammability Tester of Building Material is a device used to measure how easily certain building materials can burn or ignite. It is used to assess the flammability characteristics of different types of construction materials such as drywall, insulation, plastics and timber. The tester measures the rate at which a material combusts when exposed to an open flame from a gas-oxygen burner.

> What is surface flammability tester?

A surface flammability tester is a device that is used to test the flammability characteristics of a surface material. It is typically used to evaluate the potential fire risk of a material by measuring how easily it ignites and how quickly it burns when exposed to a flame or other ignition source.